| High-speed interface | 4×O-SMPM RF connector, 67 GHz bandwidth 8×O-SMPM RF connector, 67 GHz bandwidth (with RCNC option) |
| Modulation | PAM4 |
| Symbol rate | 53.125 GBd |
| Operation mode | Framed – 1×800G, 2×400G, 8×100G Unframed |
| Tx pre-emphasis | 7 taps (3 pre-cursors, a main cursor, and 3 post-cursors) |
| Sub-eye height tuning | Lower eye, upper eye |
| Channel polarity | Tx inversion, Rx inversion |
| Rx equalizer | Auto adaptive CTLE, 32-tap FFE, and DFE Auto adaptive CTLE, 20-tap FFE with spurious noise and reflection cancellation (RCNC mode and RCNC option required) |
| General measurements | Frequency offset, pre-FEC error (count, rate), Tx/Rx frame count, Tx/Rx line utilization, correctable codeword count, frame loss ratio, FEC margin, test time, latency, frame check sequence (FCS), etc. |
| Ethernet alarms and errors | Link down, no traffic, pattern loss, local fault detected, local fault received, remote fault, LOA, local degraded SER detected, local degraded SER received, remote degraded SER, 66B block, FEC-UNCOR-CW, FEC-COR-CW, FEC-SYMB |
| PCS alarms | LOAML, excessive skew, invalid marker |
| Rx taps (channel simulation) | Channel response table, channel response plot |
| Frame distribution | Size analysis of <64, 64, 65 to 127, 128 to 255, 256 to 511, 512 to 1023, 1024 to 1518, 1591 to 1522, >1522 |
| PCS lane info | Pre-FEC BER/SER per lane, LOMAL, excessive skew, invalid marker per lane, PCS lane mapping |
| Histogram | SNR, level deviation, threshold deviation, sub-eye height (RCNC mode and RCNC option required) |
| Frame size | 64 to 16000 bytes (fixed, EMIX) |
| L2 MAC address | Source MAC address, destination MAC address, EtherType |
| Ethernet error injection type | FEC-UNCOR-CW, FEC-COR-CW, FEC-SYMB, 66B block |
| Pattern (unframed mode) | PRBS 15Q/31Q, only PPG supports PRBS13Q, SSPRQ and user-defined pattern |
| Maximum amplitude a, b | 800 mVppd |
| PAM4 eye width (zero hit) a | 6.0 ps |
| Sensitivity c | 250mVppd and BER < e-10 250mVppd and BER < e-12 (RCNC mode and RCNC option required) |
| ED damage level | 900mVppd |
| Resource embedded | User guide, API guide, sample code |
| Clock output | Amplitude > 400 mV, Ratio /8,/16,/32, /64 (trigger) |
| Reference clock | Sync with another unit to support 1.6T (16×100G), Reference clock output amplitude > 700 mV |
| Low-speed signal control interface | 16-pin header to access transceiver through EXFO 800G MCB (QSFP-DD, OSFP, OSFP-RHS) |
| Transceiver access | Show low-speed signals, read/write I2C register |
| LAN port | TCP/IP IP address, subnet mask, default gateway, and DHCP support |
| a. PAM4 53.125 GBd signal measured by 50 GHz-bandwidth scope with 50 GHz 2.4 mm, 15 cm RF cable. b. Support overdrive 900 mVppd. c. Measured by direct loopback from PPG to ED with 67 GHz-bandwidth O-SMPM, 20 cm RF cables. All specifications are typical, at 23 °C ± 2 °C unless otherwise specified. | |
| Size (H × W × D) | 139 mm × 443 mm × 229 mm (5 1/2 in × 17 1/2 in × 9 in) |
| Weight | ≤ 10 kg (22 lb) |
| Temperature | Operating 5 °C to 40 °C (41 °F to 104 °F) Storage –20 °C to 70 °C (–4 °F to 158 °F) |
| Relative humidity | 20 % to 80 % (80 % for temperatures up to 31 °C decreasing linearly to 50 % at 40 °C) |
| Power | 100 to 127 V, 50/60 Hz 200 to 240 V, 50/60 Hz 400 W max. |